Diode Dynamics DIO Headlight Ballast Light Accessories and Wiring - DD1003S

Overview. This is a D1 compatible 35 watt HID ballast from HYLUXTEK. With true OEM-grade manufacturing these ballasts are intended to perform for years with absolutely zero failures.If you have a D1 OEM HID setup with a failed ballast you can purchase one of these to get back up and running at a fraction of the cost of a new ballast from the dealer. Check your factory wires you might not even need to do any wiring! The input and output connections on this ballast are D1 standard. However if yours is different just add the D1 input and output wires to your order. The input wire comes with a pigtail so you can simply tap the positive and negative input wires into the wires that powered your original ballast.Compatability. This ballast should be used with D1 bulbs only (D1S D1R etc). If you have a D2 bulb or a standard aftermarket AMP HID size such as 9006 H1 or H11 please use our AMP or D2 ballast instead.We recommend using high-quality D1 aftermarket bulbs with this ballast or OEM-grade bulbs such as Philips or OSRAM. For D1 size the igniter is built into the bulb and some cheap bulbs may not perform well. If you have good bulbs this ballast will work with them without any issue.Reliability. Most ballasts these days run with digital signal processing (DSP). This allows for a much smoother and more reliable power output faster warmup and longer bulb life. However most digital ballasts still use standardized computing chips to process the information. It is very cost-efficient to use standard chips off the shelf. Instead the HYLUX uses a computing chip designed specifically for the purpose of running an HID bulb. This is known as an application-specific integrated circuit (ASIC). While this is much more expensive than a generic chip it allows the HYLUX ballast to operate with extremely high efficiency and performance far exceeding that of any generic ballast on the market.

This is a D1 compatible 35 watt HID ballast from HYLUXTEK. With true OEM-grade manufacturing these ballasts are intended to perform for years with absolutely zero failures.If you have a D1 OEM HID setup with a failed ballast you can purchase one of these to get back up and running at a fraction of the cost of a new ballast from the dealer. Check your factory wires you might not even need to do any wiring! The input and output connections on this ballast are D1 standard. However if yours is different just add the D1 input and output wires to your order. The input wire comes with a pigtail so you can simply tap the positive and negative input wires into the wires that powered your original ballast.Compatability. This ballast should be used with D1 bulbs only (D1S D1R etc). If you have a D2 bulb or a standard aftermarket AMP HID size such as 9006 H1 or H11 please use our AMP or D2 ballast instead.We recommend using high-quality D1 aftermarket bulbs with this ballast or OEM-grade bulbs such as Philips or OSRAM. For D1 size the igniter is built into the bulb and some cheap bulbs may not perform well. If you have good bulbs this ballast will work with them without any issue. If you're having a problem and not sure if you need a ballast or bulb just contact us and we can help you figure it out!

This is a D1 compatible 35 watt HID ballast from HYLUXTEK. With true OEM-grade manufacturing these ballasts are intended to perform for years with absolutely zero failures.

Included in the box: One (1) HYLUX D1 HID Ballast . Weatherproof D1 Power Input and Output Wires.

Included in the box: 1 HYLUX D1 HID Ballast Weatherproof D1 Power Input and Output Wires

High Intensity Discharge (HID) Lighting Ballast

HID Ballast with OEM-grade manufacturing.

Diode Dynamics HYLUX D1 Ballast

Diode Dynamics Accessories

Diode Dynamics - DD1003S

OEM quality HID ballast

HID Ballast